• Networking
  • Programming
  • DBMS
  • Operating System
  • Internet
  • Hardware
  • Software

Tech Differences

Know the Technical Differences

Difference Between RIP and OSPF

Difference between RIP and OSPFA routing protocol describes the rules that must be followed by a router while it interacts with neighboring routers to learn the path and to maintain the network in the routing tables. The RIP and OSPF are the Interior Gateway Routing protocols which differ in many ways.

The principal difference is that RIP falls in the category of distance vector routing protocol whereas OSPF is the example of link state routing. Another difference is that RIP uses bellman ford algorithm while OSPF uses Dijkstra algorithm.

There are two varieties of routing protocols for internetworks that are IGP and EGP. IGP (Interior gateway routing protocol) is restricted to an autonomous system, which means all routers operates inside an autonomous system.

On the other hand, EGP (exterior gateway routing protocol) works for the two autonomous system means from one autonomous system to another and vice-versa. An autonomous system is a logical boundary that represents a network which works under a single common administration.

The three classes of routing protocols are

  • Distance Vector: Distance vector routing protocol finds the best path to a remote network by using the relative distance. Each time when a packet passes through a router is referred as a hop. The best route is the route which has the lowest number of hops to the network. RIP and EIGRP are the examples of the Distance vector routing protocols.
  • Link State: It is also known as shortest path first, in which each router creates three separate tables. Each table perform its different functions such as one keeps track of directly attached neighbours, the second one determines the topology of the entire internetwork, and the third one is used for the routing table. OSPF is an example of Link state routing protocol.
  • Hybrid: Uses characteristic of distance vector and link state such as EIGRP.

Content: RIP Vs OSPF

  1. Comparison Chart
  2. Definition
  3. Key Differences
  4. Conclusion

Comparison Chart

Basis for comparisonRIPOSPF
Stands forRouting Information Protocol.Open Shortest Path First
ClassDistance vector routing protocolLink State Routing Protocol
Default metricHop countBandwidth (cost)
Administrative distance120110
ConvergenceSlowFast
SummarizationAutoManual
Update timer30 secondsOnly when changes occur
Hop count limit15None
Multicast address used224.0.0.9224.0.0.5 and 224.0.0.6
Protocol and port usedUDP and port 20IP and port 89
Algorithm usedBellman-fordDijkstra

Definition of RIP

Routing Information Protocol is the straight implementation of distance vector routing for local networks. In every 30 seconds, it delivers an entire routing table to all active interfaces. Hop count is the only metrics to describe the best path to a remote network, but it can be 15 at max. It prevents routing loops, through restricting the number of hop counts permitted in the path.

There are two versions of RIP, RIP version 1 and RIP version 2 the difference between both of the versions are outlined in the following chart.

FeaturesRIPv1RIPv2
Class support ClassfulClassless
Supports variable-length subnet mask (VLSM)NoYes
Sends the subnet mask along with routing update NoYes
Communicates with other RIP router through the following address typeBroadcastMulticast
RFC definitionRFC 1058RFCs 1721, 1722, and 2453
Supports authentication NoYes

Convergence is a process of collecting the topological information or updating the information for the other routers through the implemented routing protocol. Convergence occurs when the router is transitioned from either to forwarding or blocking states, and it prevents data forwarding at that instant.

The main issue with convergence is the time it takes to update information in a device. Slow convergence can result in inconsistent routing table and routing loops. Routing loops forms when routing information is not updated or the when the information propagated throughout the network is wrong.

Split horizons and route poisoning is the solution to the routing loop problem. Split horizon enforces a rule which prevents the information form sending back to the source from which it was received. In route poisoning, when any network goes down its router simulates the network as 16 in the table entry (which is unreachable or infinite as only 15 hops are allowed). Ultimately this results in spreading the poisoned route information to all the routes in the segment.

RIP disadvantage is that it is inefficient on large networks or on networks where a large number of routers are instated.

RIP timers

  • Update timer defines how frequent a router will send out routing table update, and its default value is 30 seconds.
  • Invalid timer specifies the duration for a route till which it could remain in routing table before being considered as invalid if no new updates are aware of this route. The invalid route is not removed from the routing table rather it is marked as metric of 16, and placed in the hold-down state. The default value of the invalid timer is 180 seconds.
  • Hold-down timer indicates the duration till which a route is forbidden from receiving updates. RIP will not receive any new updates for routes when it is in the hold-down state; its default value is 180 seconds.
  • Flush timer specifies how long a route can be retained in a routing table ahead of getting flushed out when no new updates are received. Its default value is 240 seconds.

Definition of OSPF

Open Shortest Path First is a link state and hierarchical IGP routing algorithm. It is an enhanced version of RIP, which comprises features like multipath routing, least cost routing, and load balancing. Its major metric is the cost to determine the best path.

OSPF involves the type of service routing which means multiple routes can be installed according to the priority or type of service. OSPF offers load balancing in which it distributes overall traffic routes equally. It also allows networks and routers partitioned into subsets and areas which enhance the growth and ease of management.

OSPF enables (Type 0) authentication in all the exchanges between routers which means by default these interchanges over the network are not authenticated. It offers two other authentication methods, simple password authentication and MD5 authentication. It supports subnet specific, host-specific, and classless routes, also, classful network specific routes.

In OSPF the routing is done by sustaining the database with link state information in the routers and route weights computed using link state, IP address etc. The link states are transmitted all through the autonomous system to the routers to update the database. After that, each router builds a shortest path tree as a root node, on the basis of the weights stored in the database.

Key Differences Between RIP and OSPF

  1. RIP depends on hop counts to determine the best path while OSPF depends on cost (bandwidth) which helps in determining the best path.
  2. Administrative Distances (AD) measures the probity of received routing information on a router from a neighbor router. An administrative distance can vary from integers 0 to 255, where 0 specifies the most trusted integer, and 255 signifies that no traffic is allowed to pass through this route. The AD value of RIP is 120 whereas it is 110 for OSPF.
  3. Convergence in the RIP is slow in contrast it is fast in OSPF.
  4. Summarization allows a single routing table entry to illustrate a collection of IP network numbers. RIP supports auto summarization, as against OSPF supports manual summarization.
  5. There no hop count limit in OSPF. On the contrary, the RIP is limited to 15 hop counts.

Conclusion

RIP is most commonly used protocol and generates lowest overheads, but it can not be used in larger networks. On the other side, OSPF performs better than RIP in terms of cost of transmission and is suitable for larger networks. OSPF also provides maximum throughput and lowest queuing delay.

Related Differences:

  1. Difference Between OSPF and BGP
  2. Difference Between EIGRP and OSPF
  3. Difference Between Distance Vector Routing and Link State Routing
  4. Difference Between Static and Dynamic Routing
  5. Difference Between Fact Table and Dimension Table

Comments

  1. Abhijeet Waghmare says

    September 10, 2018 at 10:07 am

    Informative article. Thanks

    Reply
  2. Nancy says

    January 23, 2019 at 6:09 am

    Very good article thanks

    Reply
  3. Imed BRAHMI says

    April 25, 2019 at 4:48 pm

    Informative, thanks

    Reply
  4. Arandi Marans says

    July 9, 2019 at 7:41 pm

    Very useful and informative, thanks.

    Reply
  5. PATRICK PIZZETTI says

    October 5, 2019 at 7:11 pm

    Thanks for the very enlightening comparison.

    Reply
  6. TND says

    October 29, 2019 at 6:15 am

    Well explained,, thank you 🙂

    Reply
  7. komal pandya says

    November 1, 2019 at 8:14 am

    Nice one.

    Reply
  8. Kartheek says

    February 16, 2020 at 3:01 pm

    Thanks we’ll explained

    Reply
  9. Bretto says

    June 17, 2020 at 9:41 am

    Quality explanation

    Reply

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Top 10 Differences

  • Difference Between OLTP and OLAP
  • Difference Between while and do-while Loop
  • Difference Between Guided and Unguided Media
  • Difference Between Preemptive and Non-Preemptive Scheduling in OS
  • Difference Between LAN, MAN and WAN
  • Difference Between if-else and switch
  • Difference Between dispose() and finalize() in C#
  • Difference Between for and while loop
  • Difference Between View and Materialized View
  • Difference Between Server-side Scripting and Client-side Scripting

Recent Addition

  • Difference Between Java and Python
  • Difference Between PHP and HTML
  • Difference Between GPS and GNSS 
  • Difference Between Virtualization and Containerization
  • Difference Between Storage and Memory

Categories

  • Artificial Intelligence
  • DBMS
  • Hardware
  • Internet
  • Networking
  • Operating System
  • Programming
  • Software

Copyright © 2025 · Tech Differences · Contact Us · About Us · Privacy